Showing 1–12 of 81 results

Show sidebar
Close

0.91 Inch 128×32 I2C Blue OLED LCD Display DIY Oled Module SSD1306 Driver

৳ 500.00
Features: OLED display, no need backlight, self-illumination, the display performance is better than the traditional LCD display, also lower consumption.
Close

1S Lithium Battery Capacity Indicator

৳ 200.00
Description: 1.Battery type electricity quantity display 2.Wide application fields:lithium battery 3.Using Method:connect display board positive and negative port with tested
Close

30A Mini VNH2SP30 Stepper Motor Driver Monster Moto Shield module

৳ 500.00
 Stepper Motor Driver This is essentially a ramped up version of Ardumoto motor driver shield. For this monster shield we’ve
Close

315Mhz Key Wireless Remote Control Kits Receiver module For arduino

৳ 300.00
Remote control  1.Operating voltage: DC12V (27A/12V battery x1) 2.Operating Current: 10mA @ 12V 3.Radiated power: 10mw @ 12V 4.Modulation mode:
Close

3D printer board Ramps 1.6 control panel Reprap support DRV8825

৳ 1,250.00
Ramps 1.6:   Ramps 1.6 is optimized and launched based on Ramps 1.4 & Ramps 1.5 By Biqu The Struture almost same as Ramps 1.5 , the difference is Ramps 1.6
-27%
Close

433Mhz RF Transmitter + Receiver Module Kit for Arduino / ARM /MCU WL

৳ 150.00 ৳ 110.00
Specifications: Receiver module parameters Product Model MX-05V Operating voltage: DC5V Quiescent current: 4mA Receiving frequency: 433MHZ Receiver sensitivity:-105DB Size: 30
-10%
Close

5V 2-Channel Relay Module Shield for Arduino

৳ 145.00 ৳ 130.00
2-way relay module with opto  Module Parameters: 1 Dimensions: 50.5mm (length) * 38.5mm (W) * 18.5 (H) 2 Weight:. 31g
Close

5V 4 Channel Relay Module For Arduino 4-Channel

৳ 299.00
5V Relay Module 4-Channel This is a 5V 4-Channel Relay interface board. Be able to control various appliances, and other
Close

5V 4-Channel Relay Module Shield for Arduino

৳ 200.00
Features:   This relay module is 5V active low. It is an 4-channel relay interface board, which can be controlled
Close

5V 8-Channel Relay Module Shield for Arduino

৳ 390.00
Description: This is 5V 8 Channel relay module board for Arduino PIC AVR DSP ARM This relay module is 5V
-36%
Close

Arduino CNC/3D Printer combo pack CNC shield V3 A4988 driver

৳ 2,000.00 ৳ 1,280.00
Details: CNC Shield Board: 1,Latest CNC Shield Version 3.0 for Arduino. 2,GRBL 0.9 compatible. (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals) 3,PWM Spindle and direction pins 4,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a  full 4th axis with custom firmware using pins D12 and D13) 5,2 x End stops for each axis (6 in total) 6,Coolant enable 7,Uses removable A4988 or DRV8825 compatible stepper drivers 8,Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to  1/32 micro-stepping ) 9,Compact design. 10,Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 11,Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) 12,Please note that this is an unassembled kit and Basic soldering skills are needed. A4988 Stepper Motor Driver: 1,A4988 Stepper Motor Driver Board is a breakout board for Allegro’s A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product. Low RDS (On) Output 2,Automatic current decay mode  detection / selection 3,Mix with slow current decay modes 4,Synchronous rectification for low power dissipation
Close

Arduino Due 2012 R3 ARM Version Main Control Board

৳ 1,340.00
Note: This is not the same as other Arduino boards, the Arduino Due board runs at 3.3V. The maximum voltage that