Showing 1–12 of 15 results
3DR 100mW Radio Telemetry Kit 915MHz (v2)
3DR Telemetry Kit Specifications – Very small size – Light weight (under 4 grams without antenna) – 915MHz MHz – Receiver sensitivity to -121 dBm – Transmit power up to 20dBm (100mW) – Transparent serial link – Air data rates up to 250kbps – MAVLink protocol framing and status reporting – Frequency hopping spread spectrum … Continue reading 3DR 100mW Radio Telemetry Kit 915MHz (v2)
Anti-Vibration Set for CC3D ,APM & KK Flight Controller
Specification: – Fiberglass material – Color: Black – Suitable flight controller: CC3D, APM, kk – With rubber balls, screws and nuts
Ardupilot APM 2.8 Flight Controller Board with Protective Case
Ardupilot APM 2.8 Flight Control Board Bend Pin with Protective Case Specification: Item Name: APM 2.8 Flight Control Board Features: Arduino Compatible! Includes 3-axis gyro, accelerometer, along with a high-performance barometer Onboard 4 MegaByte Dataflash chip for automatic datalogging Optional off-board GPS, uBlox LEA-6H module with Compass. One of the first open source autopilot systems … Continue reading Ardupilot APM 2.8 Flight Controller Board with Protective Case
ArduPilot Mega APM 2.8 Flight Controller + UBLOX NEO-7M GPS
APM V2.8.0 Flight Controller Upgrade Verstion 2.6 2.5.2 for Multirotor Fixed Wing APM V2.8.0 description: – This version eliminates the 1.0mm 6P SM06B GPS interface of V2.52 old version, and change it into DF13-4P I2C external compass interface. – Put DF13-5P GPS interface with external compass interface, convenient for the connection of GPS and externalcompass. … Continue reading ArduPilot Mega APM 2.8 Flight Controller + UBLOX NEO-7M GPS
Betaflight F4 Pro V3 Flight Controller Built-in OSD Barometer
Specification: Item name: betaflight F4 V3 Flight Controller Size: 36x36mm Mount holes: 30.5×30.5mm Features: -STM32 F405 MCU -Dshot support -Drag and Drop OSD configured via Betaflight Configurator -Smartaudio v2 support – Tune your PID’s and configure the omnibus F C from your Transmitter -MPU6000 6 axis SPI Gyro & Accelerometer -SBUS/PPM AND Spketrum dsm-x … Continue reading Betaflight F4 Pro V3 Flight Controller Built-in OSD Barometer
Betaflight F4 V2 PRO Flight Controller Board w/ Baro Built-in OSD
Betaflight OMNIBUS F4 Pro (V2) Flight Control Built-in OSD / BEC for FPV Racing Drone DIY Quadcopter Hardware parameters: STM32 F405 MCU MCU Barometer BMP280 The six-axis sensor MPU6000 uses an SPI connection Standard SD card slot MCU through the SPI bus DMS mode control OSD chip, faster Built-in power module BEC, no external, easy … Continue reading Betaflight F4 V2 PRO Flight Controller Board w/ Baro Built-in OSD
CC3D Open Pilot Atom Mini CC3D Flight Controller
CC3D CopterControl Hardware Features Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac and Linux. Direct high speed USB support with no drivers required, … Continue reading CC3D Open Pilot Atom Mini CC3D Flight Controller
Deluxe F3 Flight Controller with Built-in OSD 6DOF Acro
The Deluxe F3 Flight Controller with OSD was designed to give outstanding flight performance based on tried and tested sensors while providing unparalleled I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU. Integrated On-Screen Display uses MWODS firmware and is compatible with flight controllers running Cleanflight, Betaflight & Baseflight. Space-saving design … Continue reading Deluxe F3 Flight Controller with Built-in OSD 6DOF Acro
DJI Naza-M Lite Multi-Rotor Flight Controller
All-In-One Design For entry-level enthusiasts, DJI now brings out the most cost-effective solution, the NAZA-M Lite flight control system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer … Continue reading DJI Naza-M Lite Multi-Rotor Flight Controller
F3 Flight Controller Acro 6 DOF for Multirotor Racing
Racing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performance based on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU. The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you’re into FPV racing, … Continue reading F3 Flight Controller Acro 6 DOF for Multirotor Racing
KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
The next evolution of the rotor revolution is here!! The KK2.1.5 is packing new found power with updated sensors, memory and header pins. The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. … Continue reading KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
Matek F405-STD BetaFlight STM32F405 Flight Controller Built-in OSD
Specification (user manual): Brand: Matek Systems Item name: Flight Control Board Size: 36x36mm Mounting hole: 30.5mm Weight: 7g MCU: 168MHz STM32F405RGT6 IMU: 32K ICM20602 gyro/accelerometer (SPI) Baro: BMP280 (I2C) OSD: BetaFlight OSD w/ AT7456E chip Blackbox: MicroSD card slot (SD/SDHC) VCP, UART1, UART2, UART3, UART4, UART5 Built in inverter for SBUS input (UART2-RX) PPM/UART Shared: … Continue reading Matek F405-STD BetaFlight STM32F405 Flight Controller Built-in OSD